Journal of Guilan University of Medical Sciences
مجله علوم پزشکی گیلان
JGUMS
Literature & Humanities
http://journal.gums.ac.ir
1
admin
2383-4307
2423-4818
10.32598
fa
jalali
1390
1
1
gregorian
2011
4
1
20
77
online
1
fulltext
fa
بررسی مقایسهای ریزنشت انواع کامپوزیت، گلاس اینومر تغییر یافته با رزین در ترمیمهای کلاس V
Evaluating the Microleakage of Class V Cavity Preparations Restored with Resin Composite and Resin Modified Glass Ionomer
تخصصي
Special
پژوهشي
Research
چکیده مقدمه: ایجاد تطابق و بههم رساندن لبهای در حفرههای کلاس V(CLV) و شناخت بهترین ماده ترمیمی برای کاهش میزان ریز نشت در آنها یکی از چالشهای مهم در دندانپزشکی ترمیمی است. هدف: بررسی ریزنشت سه نوع کامپوزیت و یک گلاس اینومر تغییر یافته با رزین در حفرات CLV. مواد و روشها: در سطح باکال 32 دندان پرمولر حفرات CLV، به صورتی تراشیده شد که لبه الکوزالی حفره در مینا و لبه جینجیوالی آن در عاج قرار داشتهباشد. دندانها به چهار گروه 8 تایی تقسیم و با مواد زیر طبق توصیه کارخانه سازنده(3M) ترمیم شدند: گروه اول: کامپوزیت میکروهیبرید (Z250)، گروه دوم: کامپوزیت نانوفیل (Supreme)، گروه سوم: کامپوزیت Flowable و گروه چهارم: گلاس اینومر تغییر یافته با رزین (Vitremer). نمونهها پس از ترموسیکل، در محلول 50 درصد وزنی نیترات نقره به مدت 4 ساعت و سپس در محلول ظهور به مدت 8 ساعت قرار دادهشدند و پس از برش باکولینگوالی با استریومیکروسکوپ بررسی شدند. درجه ریزنشت ثبت و یافتهها با دو آزمون آماری Kruskal- wallis و mann- whitney ارزیابی شد. نتایج: در هیچ کدام از نمونهها ریزنشت در لبه مینایی وجود نداشت. در لبه عاجی، Vitremer و کامپوزیت Flowable به ترتیب کمترین و بیشترین میزان ریزنشت را داشتند (05/0< P). بین گروههای دیگر در لبه عاجی تفاوت معنیدار وجود نداشت. نتیجهگیری: بهترین نتایج از لحاظ کاهش ریزنشت در لبه عاجی، مربوط به vitremer و ضعیفترین آنها مربوط به کامپوزیت flowable بود.
Abstract Introduction: Marginal seal in class V Cavities and determining the best restorative material to decrease microleakage of them is very important in operative dentistry. Objective: To evaluate the microleakage of class V cavity preparations restored with three different types of resin composite and resin modified glass Ionomer. Materials and Methods: Two class V cavities were prepared in buccal surface of 32 recently extracted premolar teeth. The occlusal margin of each restoration was on enamel and the gingival margin on dentin. Teeth were randomly assigned to four groups of 8 teeth and restored as follows: Group I: microhybrid resin composite (Z250) Group II: nano composite (supreme) Group III: Flowable composite (3M) Group IV: resin modified glass Ionomer (vitremer). In all groups, the manufacture instructions were strictly followed. All teeth were immersed in 50% Silver Nitrate during 4 hours and developing solution for 8 hours after thermocycling. The teeth were longitudinally sectioned and observed under a stereomicroscope. The degree of dye penetration was recorded and analyzed with the kruskal-wallis and mann-whitney test. Results: There was no evidence of microleakage on the enamel margins in any groups. When the margins were in dentin, vitremer and flowable composite had the less and the most level of microleakage in dentinal margine respectively (p<0.05). There was no significant differents in other groups of dentinal margin. Conclusion: Vitremer has an efficterness role and flawable composite has a weakness role in reducting microleakage of dentinal margin.
میکرولیکیج, کلاس V, کامپوزیت, گلاس آینومر
Microleage, ClV, Composite, Glass Ionomer
8
14
http://journal.gums.ac.ir/browse.php?a_code=A-10-36-76&slc_lang=fa&sid=1
F
Falahzadeh
فرنوش
فلاحزاده
drfarnooshfal@yahoo.com
Yes
Ghazvin University of Medical Sciences
دانشگاه علوم پزشکی قزوین
A
Yousefi
عاطفه
یوسفی
No
Ghazvin University of Medical Sciences
دانشگاه علوم پزشکی قزوین
A
Parsafar
آذر
پارسافر
No
Ghazvin University of Medical Sciences
دانشگاه علوم پزشکی قزوین